Other Quality Accessories

Chisel with Roller - Solid Tipped   New solid chisel cutting edge for better control when removing glazing after it has been heated. Roller is fixed. Adjust the depth by bringing the handle up (cutting deeper) or bringing the handle down (cutting shallower). This tool is a necessity when restoring old window sashes. Tool made in England.

# 1200-11
Price: $31.00

Putty Chisel   Handy scraper for removing residual window glazing on the sash and the window glass. Can also be used to apply window glazing.

# 1200-1
Price: $15.00

Boiled Linseed Oil   This is a natural oil made from flax. For mixing in paint and preserving wood. One quart.

# 646148 / 1 Liter
Price: $18.00

# 646148-5 / 5 Liters
Price: $85.00

Heat-Resistant Aluminum Tape   Protect areas from high temperatures and infrared heat with this self-adhesive tape. Will not breakdown when heated. Works great during window restoration and for other areas you need to protect.

# 1200-T
Price: $15.00

Slow Speed Grinder   Slow Speed Grinder for sharpening scraper blades. Quiet, smooth 3/4 HP, 1725 RPM slow speed grinder, great for sharpening scraper blades without generating the heat that you get so quickly from 3450 RPM grinders. Unlike most grinders, which include cheap useless gray wheels, this slow speed grinder comes equipped with 1" x 8" 120 grit & 1" x 8" 60 grit white aluminum oxide grinding wheels.

# 144290
Price: $135.00

Sharpening Station w/ Jig & Blade Holder   Includes everything you need to effectively sharpen your blades. Quiet, smooth 3/4 HP, 1725 RPM slow speed grinder, great for sharpening scraper blades without generating the heat that you get so quickly from 3450 RPM grinders. Next best to a wet-wheel but much faster. Unlike most grinders, which include cheap useless gray wheels, this slow speed grinder comes equipped with 1" x 8" 120 grit & 1" x 8" 60 grit white aluminum oxide grinding wheels. Also includes the Blade Jig and our praised Blade Holder. Cut and place the grinder on an 8" x 8"piece of plywood. Cut another piece of plywood 16" x 8". Place the grinder and the 8" x 8" plywood base on top of the larger plywood piece. Bolt both pieces of the plywood and the grinder together centered with two bolts. Screw the jig right underneath the fine wheel. The grinder needs to be raised up approximately 3/4" to clear the jig (see picture). You can clamp this set-up on a table or bolt it onto a pedestal stand.

# 144291
Price: $225.00

Blade Sharpening Jig   Very useful item to guide the blade when you are sharpening our hardened steel blades. It is possible to sharpen the blades without removing the blade from the handle. Maintaining the same angle of the scrapers blade is essential to get an effective scraper. This jig can be utilized on any grinder. Use a 1750 rpm grinder. A faster grinder may destroy the hardening in the steel. Mount the jig on a plywood platform under the grinder wheel and cut another piece of plywood for the base of the grinder raising the grinder up approximately 3/4". Note: Blade sharpener is not included.

# J100
Price: $95.00

Blade Holder   Blade holder for blade sharpening jig. Excellent for holding Triangular, Clapboard, Window & German siding blades on our sharpening jig.

# 1234
Price: $31.00

Infrared Replacement Bulbs  Infrared replacement bulbs for The Silent Paint Remover Model 1100-14. Bulb life expectancy is 5000 hours. It is suggested only to buy these when needed.

# 1100-15
Price: $85.00

Screwdriver Repair Set   These tools are needed to change the IR bulbs or clean/service your Silent Paint Remover. Kit includes one 4mm flathead screwdriver and one torx wrench.

# 1200-R
Price: $18.00

Replacement Bulbs with Screwdriver Repair Set   Includes 2 sets of replacement IR tubes for back-up with screwdriver kit and CarryCase.

# 1200-IR
Price: $198.00

Carrying Case   A convenient way to store all of your scrapers. Each CarryCase is lined with soft foam. The scrapers & blades fit snugly inside. The CarryCase also provides a safe place to store your replacement IR tubes.

# 1200-C
Price: $42.00

3M Respirator   Respirator made by 3M for lead paint removing 3M respirator recommended for lead Paint Removal. Also for: Reducing exposure to dusts from wood working and sanding painted surfaces. Where lead containing coating are present , use for reducing exposure to dusts from manual demolition of structures (e.g. drywall), scraping, manual sanding, and power tool cleaning with dust collection systems. For information and assistance on 3M Health and Safety Products call 3M tech line at 1 800 243 4630. At least 99.97 filtration against solid dust. NIOSH Approved: N100

# N100
Price: $15.00

Maintaining A Lead-Safe Home   A clearly written 'How - To' book that can give you critical information about lead risks in your home or apartment. It details steps an individual can take to minimize or eliminate the problem, and also what step you should take if you decide to hire a professional.

About the author: Dennis Livingston has long hands on experience with lead safety issues and has worked as a consultant for HUD and other government agencies. Book is endorsed by Andrew Cuomo, Secretary U.S. Dept of Housing and Urban Development.

# 1300-B
Price: $10.00